A lamicoid is a plate of two-layer engraving plastic: a thin coloured face over a contrasting core. We engrave through the face so the letters show in the core colour, which makes the lettering permanent — it won’t rub, fade or peel off the way a printed sticker does.
- Electrical panel nameplates and breaker labels
- Disconnects, transformers, MCCs and motor starters
- Junction boxes, equipment and valve tags
- Room and door ID
- Safety, caution and PPE signs
Every plate is cut and engraved on our own CNC router in Winnipeg. Single-line engraving with a V-bit gives clean, crisp letters, with a bevelled edge that shows the core colour all the way round.
Four ways to order
A whole job or a single plate. For a full set, let us read the drawings rather than designing each plate by hand.
Upload blueprints
Send the drawing set as a PDF. We read the electrical sheets and list every plate they call for. You check the wording, then order the set.
Upload drawings →
Photo of a panel
No drawings? Take a picture of the panel’s directory card. We read the circuits and lay out the nameplate and a label for every breaker.
Send a photo →
Build a panel
Draw your panel breaker by breaker: poles, amps and what each one feeds. We make every label and the nameplate, and you print the panel directory for the door.
Build the panel →
Build it yourself
Pick the size and colours, type the words, add icons, or describe the plate and Higgins lays it out. Ideal for small sets of a few templates you want to customize.
Open the Plate Designer →
Colours and what they usually mean
| Plate / letters | Usually for |
|---|---|
| ABCABC White / black, black / white | Ordinary panel, breaker and equipment labels |
| ABC Red / white | Fire alarm, fire pump, emergency, emergency power |
| ABC Yellow / black | Caution and hazard warnings |
| ABC Orange / black | Warnings; often emergency or life-safety circuits |
| ABC Green / white | First aid, safety equipment, muster points |
| ABC Blue / white | Mandatory actions and PPE |
| ABC Grey / white | Whatever your scheme calls for |
Many projects set their own colour scheme — normal power, emergency and UPS in different colours, or one colour per voltage. It’s usually in the electrical specification, often Division 26 “Electrical Identification”. If your job has a spec, follow it; your engineer or inspector has the final say.
Sizes and lettering
Common sizes are 2×½ inches for breaker labels, then 3×1, 4×1, 4×2, 5×3 and 6×2 inches. Custom sizes are fine. Main lines are usually ¼″ letters, second lines ⅛″ to 3⁄16″, in capitals with the usual short forms: PANEL A / 120/208V 3PH 4W / FED FROM MDP.
Mounting
Adhesive backing for smooth, clean indoor surfaces. Screws or rivets through ⅛″ holes — two at the ends or four in the corners — for panel covers, outdoor plates and anything that has to stay put.
Plate questions
What is a lamicoid?
An engraved plate of two-layer plastic: a thin coloured face over a contrasting core. Engraving cuts through the face so the letters show in the core colour, so the lettering can’t rub, fade or peel off like a printed sticker. Also spelled lamacoid.
Can you make every plate for a whole job from the drawings?
Yes. Upload the drawing set as a PDF and we read the electrical sheets and list every plate they call for: panel nameplates, breaker and equipment labels, outdoor plates. You check the wording, answer any questions, and order the set.
What colours should I use?
Black and white for ordinary panel and equipment labels, red with white letters for fire alarm and emergency, yellow with black for caution. Many projects set their own scheme in the electrical specification (often Division 26, Electrical Identification); if you have a spec, follow it.
Adhesive or screws?
Adhesive backing suits smooth, clean indoor surfaces like breaker labels. Use screws or rivets through mounting holes for panel covers, outdoor plates or anything that has to stay put.
Can I order just one plate?
Yes. Design it in the Plate Designer and the price shows as you go, whether it’s one plate or fifty.
